CCR Gear with Full Warranties & Fast Free Shipping

Oxygen Sensors for Diving

Our R-22DR with the standard 3-pin Molex connector is equivalent to the Teledyne R-22D and is actually our part number for the Analytical Industries PSR-11-39-MD. This sensor is used in the Dive Rite O2ptima, Jetsam KISS Classic, Innerspace Megalodon and older APD Inspiration rebreathers. It's also used in some third party controllers and dive computers such as the Juergensen Marine Hammerhead, HydroSpace Explorer, Shearwater Research GF and most DeltaP Technologies VR2 and VR3 monitoring cables.

Our R-22APDR with the coax SMB connector is equivalent to the Teledyne R-22AP (sold exclusively by APD as the ADP10) and is actually our part number for the Analytical Industries PSR-11-39-APD. Currently the SMB connector is used only in APD Evolution rebreathers and in newer (or upgraded) APD Inspiration rebreathers. While some people are using the AI sensor in APD rebreathers, please be aware that APD's position is they have tested and qualified only their own APD10 version sensor and will only warrant correct operation of their rebreathers with the APD10.

For those who use the mono-plug connector, our R-17DR with the 3.5mm mini-jack is equivalent the Teledyne R-17D and is actually our part number for the Analytical Industries PSR-11-39-JD. This sensor is used in the Closed Circuit Research Ouroboros rebreather. In early 2007, Delta P began switching their monitoring cables for the VR2 and VR3 to use this mono-plug version. It's also widely used in handheld oxygen analyzers, but see our note below.

Features

• Output 8.5-13mv (10mv +/- nominal)
• Accuracy within +/- 1% of full scale
• Response time is 6 seconds
• Conformal coating
• Temperature compensated
• Hydrophobic membrane

Factory-fresh, our sensors have a shelf life of 24 months, provided the factory-sealed gas barrier packaging bag has not been opened.

Many handheld oxygen analyzers for verifying cylinder contents use a medical grade oxygen sensor. The oxygen sensors for diving have a 'hydrophobic membrane', which is a necessity for rebreather applications, but will slightly slow (by two or three seconds) the response time of handheld O2 analyzers. This is true for any diving sensor, not just ours and to be clear does not affect the accuracy of the analysis, just the response time of the sensor. However, the medical versions are often more difficult to find and much more expensive. If you have been using an R-17D type diving sensor in your handheld unit, such as the Dive Rite VTI, Mini-Ox brand, Spectrum brand, Vandagraph VN202, El Cheapo/Expedition, or Teledyne AD300/MD3 and have been satisfied with it, by all means order the R-17DR from us.

Tek Tip

Oxygen Sensor Life in Rebreathers When any new oxygen sensor is removed from the sealed bag, it can take a few minutes to a few hours for it to acclimate and the millivolt output to stabilize. We recommend waiting 12 hours before calibrating your rebreather with a freshly opened sensor. Once acclimated, a new sensor should output approximately 10 to 15 millivolts in air and 50 to 60 millivolts in pure oxygen. In actual use in rebreather applications, all brands of oxygen sensors seem to last between one and two years. In rebreather applications, we recommend discarding any sensor acclimated at 1 ATA with less than 40 mv output in pure oxygen or less than 9 mv in air. As oxygen sensors reach end-of-life they can become unpredictable, causing problems that are sometimes difficult to diagnose. Because oxygen sensors are critical to operational safety of the rebreather, some divers annually replace all oxygen sensors rather than wait for one to reach end-of-life at a most inconvenient time. read our article 'Oxygen Sensor Handling - Best Practices'

© Copyright 2008   |   Terms & Conditions   |   Privacy Statement