CCR Gear with Full Warranties & Fast Free Shipping

Toll-Free 866-498-6857

Many of these items, found elsewhere on our website, are collected
together on this page because of their popularity with rebreather divers.

Dive Rite Offset D-ring - The rigid, Offset D-Ring attaches to the 2-inch webbing of the shoulder harness and extends out from behind rebreather counterlungs for easier attachment of bailout bottles. It is also ideal for sidemount divers for attaching tank bungees. Made of 316 stainless steel, this version is not too big and will not bruse your arm.  [More...]

Dive Rite "Tek Tote" Tool Bag - Designed like a doctor's bag, the "Tek Tote" Tool Bag is an all-around carrying case for regulators, lights, tools and dive accessories. Constructed of 600 denier nylon with foam padding and a bottom stiffener, the 16" long x 10" wide x 10" deep bag is durable and designed to protect fragile dive gear. The interior has a full length zippered pocket on one side and slip pockets on the opposite side. What makes this tool bag uniquely suited to divers is the stainless steel hardware and frame along with the s/s grommets in the base to provide drainage.  [More...]

IANTD Oxygen and Diluent Decals - These 4" X 10" decals are durable and are the international versions from IANTD, with the words Oxygen and Diluent in the center and also translated to several languages in the border.  [More...]

Dive Rite 500-Lumen LED Light - With a light output equal to HID, small size, and 12-hour burn time, this LED light is perfect for rebreather divers. The compact canister design with the switch on the head, not on the canister, means the canister can be located on or even inside the rebreather housing.  [More...]

Vandagraph VN202 Oxygen Analyzer - Because there is no flow during analysis, there is a minimum of gas waste, making this analyzer a favorite with rebreather divers. Because the unit is calibrated in still ambient air, no separate compressed air source is required for calibration. A calibration in air at 20.9% should give a typical error of just +/- 0.5% in 100% Oxygen with exceptionally fast response times.  [More...]

Mouthpieces - Rebreather Express offers a variety mouthpieces popular for reducing the jaw fatigue experienced by some rebreather divers. The Aqualung Comfo-Bite™ and the Dive Rite Long Bite mouthpieces will fit most DSV's. We also stock the SeaCure Hi-Flow moldable mouthpieces.  [More...]

Deluxe IP Gauge - Quickly check and adjust regulator intermediate pressures by plugging in to the low-pressure QD BC hose. The Deluxe IP Check Gauge makes precise IP adjustment faster with easy to use bleed (twist in either direction) that gives a quick vent and an over-pressure relief valve set at 200 psi. The large 2-inch diameter gauge has a protective rubber boot and dual scales with accuracy of 1.5% throughout the entire range.  [More...]

Tek Tip

Regulator Intermediate Pressure on Rebreathers The intermediate pressure of the Oxygen regulator on rebreathers is critical to their proper operation. Even slightly out-of-range values will shorten battery life on eCCR's due to excess energy required to open the solenoid. Significantly high values will cause the solenoid to fail closed, or manual valves to dibble. Slightly out-of-range values typically indicate the need for just a simple IP adjustment to compensate for wear. Significantly out-of-range values, particularly with "creep," often indicate a more serious impending high-pressure seat failure. Slow recovery time can indicate a clogged inlet filter. Caution: For regulators on rebreathers the correct IP setting may be different than the typical 140 psi of most open-circuit regulators. For example, the oxygen IP for the O2ptima eCCR is 90 psi and the Inspiration eCCR is 110 psi.

Second Stage Omni-Swivel - Supplied by OmniSwivel International, this very high quality omni-directional swivel screws inline between the low-pressure hose and the second stage. Offering complete 360° rotation, it allows the low-pressure hose to exit the second stage at any angle you choose. The swivel movement allows the regulator mouthpiece to move without restriction. Moving your head in any direction will not cause the second stage to pull on your jaw. This adapter makes the regulator feel much more comfortable in your mouth on waist-mounted deco and stage cylinders where the hose runs down your chest rather than over your shoulder.

First Stage Pivot-Swivels - Supplied by OmniSwivel International, this very high quality swivel screws inline between the hose and the first stage regulator body. It allows more movement of the hose at the first stage,and can be used to streamline the area of the first stage by providing tighter hose routing. The low-pressure version has 3/8-inch M-F fittings and the high-pressure version is 7/16-inch M-F fittings.

High Flow Quick Disconnect System - Supplied by OmniSwivel International, the quick disconnect system offers high-flow performance (unlike a typical BC quick disconnect). The quick disconnect slider has 9/16-inch male threads that attach to a standard low-pressure regulator hose, accepts the nipple with a positive locking mechanism which prevents accidental disconnection, and automatically seals when disconnected. We offer two different versions of the nipple fitting. One version of the QD nipple fitting attaches to the standard 9/16-inch threads found on most second stages. The other version of the QD nipple fitting screws into the standard low-pressure regulator hose 9/16-inch fitting.

2nd Stage Quick Connection Adapter - Supplied by OmniSwivel International, The regulator quick connection adapter fitting attaches to the standard 9/16-inch threads found on most second stages and the other end has a standard BC inflator male QD post. This tool allows a diver to plug a second stage into rebreather manual addition hose to allow access to the onboard gas supply. Typically the adapter would be used to gain access to the onboard oxygen but could be used for shallow access to diluent as well. The 2nd Stage Quick Connection Adapter will not supply adequate gas if the diver is deeper than 20 feet.

In-Line Shutoff Slide Valve - Supplied by OmniSwivel International, this very high quality shutoff valve fits in-line between your low-pressure hose and second stage regulator. The shutoff valve opens and closes very quickly by sliding (ON is toward the Second Stage) , and provides positive tactile feedback when operated. Used to prevent gas loss from dribbling or free flowing second stage or rebreather ADV, or whenever the ability to very rapidly stop gas flow is required. The regulator first stage should also have an OPV if the shutoff is used to disable the only pressure relief path.

In-Line Shutoff Slide Valve - This Asian manufactured alternative to OmniSwivel version of the in-line shutoff slide valve is significantly smaller and a bit lower cost. It also has a different feel to the slide valve operation that requires less force to open and close with less of a positive "detent" (also, ON is toward the hose, not the second stage). As with any cutoff, the regulator first stage should also have an OPV if the shutoff is used to disable the only pressure relief path.

Y-blocks - Supplied by OmniSwivel International, these Y-blocks provide the ability to split a single low pressure supply line to service two or three devices such as BC, drysuit, and second stage regulator. Comes standard configured with two or three 3/8-inch female ports and a 9/16-inch female port. Install a 9/16-inch male to 3/8-inch female adapter for use with a 3/8-inch M-M low pressure hose. Install a 9/16-inch male-male union for use with a standard low pressure hose with the typical 9/16-inch female fitting.

2nd Stage Cap - Supplied by OmniSwivel International, the 2nd Stage Cap seals the standard 9/16-inch fitting found on most regulator second stages. When the supply hose is disconnected, it protects the inlet threads when traveling and prevents contaminants from entering. Also recommended for the O2ptima rebreather to cover the external threads of the oxygen solenoid inlet port when not in use.

Regulator Port Plugs -- Supplied by OmniSwivel International, for standard 7/16-inch high-pressure ports and standard 3/8-inch low-pressure ports, use a hex key to install or remove. Includes the Viton oxygen-compatible O-ring. The rare 1/2-inch low-pressure port plug is also available.

 [More Fittings and Adapters...] 

Image	Item		Description	Ship	Price
	HW1109		Rigid D-Ring, Offset, S/S	Today	$11.00
	LW413		Tek Tote Tool Bag, Large	Today	$129.00
	D-OXYGEN		IANTD International Oxygen Decal	Today	$5.00
	D-DILUENT		IANTD International Diluent Decal	Today	$5.00
	VN202		Vandagraph Oxygen Analyzer	Today	$399.00
	CBMP		Comfo-Bite Regulator Mouthpiece w/tie wrap	Today	$13.95
	RG1426		Long Bite Mouthpiece w/tie wrap	Today	$4.50
	INV-CX0221		Deluxe IP Gauge	Today	$49.95
	O m n i - S w i v e l   I n t e r n a t i o n a l
		Click here to see more adapters and fittings
	OSI-SOV2		Inline Shutoff Valve: 9/16-inch M and 9/16-inch FI	Today	$52.99
	INV-HO0501		Compact Inline Shutoff Valve	Today	$24.95
	OSI-SW-S		Omni-Swivel, LP 2nd Stage: 9/16-inch M and 9/16-inch FI	Today	$70.99
	OSI-PS-LP		Pivot-Swivel, LP 1st Stage: 3/8-inch M and 3/8-inch F	Today	$47.99
	OSI-PS-HP		Pivot-Swivel, HP 1st Stage: 7/16-inch M and 7/16-inch F	Today	$47.99
	OSI-MBZ-2		Y-Block: two port 3/8-inch F and one 9/16-inch F	Today	$32.99
	OSI-MBZ-3		Y-Block: three port 3/8-inch F and one 9/16-inch F	Today	$37.99
	OSI-SYM-YM		Union: 9/16-inch M and 9/16-inch M	Today	$13.99
	OSI-SZF-YM		Adapter: 3/8-inch F and 9/16-inch M	Today	$13.99
	OSI-QDF-YM		Quick Disconnect: QD F and 9/16-inch M	Today	$71.99
	OSI-QDM-YFI		Quick Disconnect: QD M and 9/16-inch FI	Today	$20.99
	OSI-QDM-YM		Quick Disconnect: QD M and 9/16-inch M	Today	$14.99
	OSI-QDBC-YFI		Adapter, LP 2nd Stage: 9/16-inch FI to BC inflator QD Post	Today	$16.99
	OSI-DCS		Dust Cap, LP 2nd Stage: 9/16-inch FI	Today	$16.99
No surprise costs.     No Tax and shipping is FREE for US orders over $50.

Having trouble finding something?     Type one or two words into the text box above.  Then click the Search button to search our site.

Still having trouble? Send an e-mail, or call us (Toll-Free) at 866-498-6857 Mon-Fri, 9:00 am - 5:00 pm Eastern We'll see what we can do for you.

Home  |   About Us  |   Contact Us  |   Training Center  |   Library  |   Policies © Copyright 2008   |   Terms & Conditions   |   Privacy Statement